Meyer Sound UPQ-D2 Large Loudspeaker - Remote Monitoring System - Weather Protection - 3-Pin XLR

Meyer Sound UPQ-D2 Large Point-Source Loudspeaker with Remote Monitoring, Weather Protection, and 3-Pin XLR

The UPQ-D2 is a game-changer! It offers a focused beamwidth for precise coverage and minimal interaction with walls and neighboring speakers in arrays. Ideal for small to mid-sized venues, houses of worship, theaters, and nightclubs. Whether you use it as a stand-alone speaker or part of an array, it's a top choice.

Features:

• • Wide horizontal pattern for broad listening areas and focused vertical pattern for precise coverage
• • High-energy efficient amplifier with digital signal processing for flat amplitude and phase response
• • Integral stand mount and QuickFly mounting options for easy rigging

Specifications:

• Acoustical:
  • Operating Frequency Range: 55 Hz – 18 kHz
  • Frequency Response: 58 Hz – 18 kHz ±4 dB
  • Phase Response: 80 Hz – 18 kHz ±45°
  • Linear Peak SPL: 138 dB with 19 dB crest factor (M-noise), 134.5 dB (Pink noise), 137 dB (B-noise)
• Coverage:
  • Horizontal Coverage: 50° horizontal x 50° vertical (-6 dB)
  • Vertical Coverage: 60° horizontal x 60° vertical (-10 dB)
• Transducers:
  • Low Frequency: One high-power 15-inch cone driver with neodymium magnet; 2 Ω nominal impedance
  • High Frequency: One 4-inch diaphragm compression driver; 8 Ω nominal impedance
• Audio Input:
  • Type: Differential, electronically balanced
  • Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
  • Connectors: XLR 3-pin female input with male loop output
  • Input Impedance: 10 kΩ differential between pins 2 and 3
  • Wiring:
    • Pin 1: Chassis/earth through 220 k, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
    • Pin 2: Signal +
    • Pin 3: Signal -
    • Case: Earth ground and chassis
  • Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
  • Input Level: Audio source must be capable of producing of +20 dBV (10 V rms) into 600 to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
• Amplifier:
  • Type: Two-channel, Class-D
  • Total Output Power: 2250 W peak
  • THD, IM, TIM: < 0.02%
  • Cooling: Convection
• AC Power:
  • Connectors: PowerCON 20 input with loop output
  • Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
  • Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
  • Turn-on and Turn-off Points: 90 V AC turn-on; no turn-off; internal fuse-protection above 265 V AC
• Current Draw:
  • Idle Current: 0.27 A rms (115 V AC); 0.25 A rms (230 V AC); 0.29 A rms (100 V AC)
  • Maximum Long-Term Continuous Current (>10 sec): 2.0 A rms (115 V AC); 1.0 A rms (230 V AC); 2.3 A rms (100 V AC)
  • Burst Current (<1 sec): 3.6 A rms (115 V AC); 1.8 A rms (230 V AC); 4.1 A rms (100 V AC)
  • Maximum Instantaneous Peak Current: 7.8 A pk (115 V AC); 4.0 A pk (230 V AC); 9.1 A pk (100 V AC)
  • Inrush Current: < 20 A peak
• RMS Network (Optional): Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system operator's host computer.
• Physical:
  • Dimensions: W: 19.00 in (483 mm) x H: 28.15 in (715 mm) x D: 18.18 in (462 mm)
  • Weight: 95 lb (43 kg)
  • Enclosure: Premium multi-ply birch with slightly textured black finish
  • Protective Grille: Powder-coated, hex-stamped steel with black mesh
  • Rigging: Aluminum end plates on top and bottom with metric M10 threaded points; integral 1.5-inch (38 mm) pole mount receptacle on bottom

The Meyer Sound UPQ-D2 is a large point-source loudspeaker designed for small to mid-sized venues, houses of worship, theaters, and nightclubs. It features a focused beamwidth for precise coverage and minimal interaction with walls and neighboring speakers. With its wide horizontal pattern and focused vertical pattern, it provides broad listening areas and precise coverage. The high-energy efficient amplifier with digital signal processing ensures flat amplitude and phase response. It has integral stand mount and QuickFly mounting options for easy rigging. The dimensions are W: 19.00 in (483 mm) x H: 28.15 in (715 mm) x D: 18.18 in (462 mm), and it weighs 95 lb (43 kg).